SNMP-NOTIFICATION-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, snmpModules FROM SNMPv2-SMI RowStatus, StorageType FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB SnmpTagValue, snmpTargetParamsName FROM SNMP-TARGET-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; snmpNotificationMIB MODULE-IDENTITY LAST-UPDATED "9808040000Z" ORGANIZATION "IETF SNMPv3 Working Group" CONTACT-INFO "WG-email: snmpv3@lists.tislabs.com Subscribe: majordomo@lists.tislabs.com In message body: subscribe snmpv3 Chair: Russ Mundy Trusted Information Systems Postal: 3060 Washington Rd Glenwood MD 21738 USA EMail: mundy@tislabs.com Phone: +1-301-854-6889 Co-editor: David B. Levi SNMP Research, Inc. Postal: 3001 Kimberlin Heights Road Knoxville, TN 37920-9716 EMail: levi@snmp.com Phone: +1 423 573 1434 Co-editor: Paul Meyer Secure Computing Corporation Postal: 2675 Long Lake Road Roseville, MN 55113 EMail: paul_meyer@securecomputing.com Phone: +1 651 628 1592 Co-editor: Bob Stewart Cisco Systems, Inc. Postal: 170 West Tasman Drive San Jose, CA 95134-1706 EMail: bstewart@cisco.com Phone: +1 603 654 2686" DESCRIPTION "This MIB module defines MIB objects which provide mechanisms to remotely configure the parameters used by an SNMP entity for the generation of notifications." REVISION "9808040000Z" DESCRIPTION "Clarifications, published as RFC2573" REVISION "9707140000Z" DESCRIPTION "The initial revision, published as RFC2273." ::= { snmpModules 13 } snmpNotifyObjects OBJECT IDENTIFIER ::= { snmpNotificationMIB 1 } snmpNotifyConformance OBJECT IDENTIFIER ::= { snmpNotificationMIB 3 } -- -- -- The snmpNotifyObjects group -- -- snmpNotifyTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpNotifyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to select management targets which should receive notifications, as well as the type of notification which should be sent to each selected management target." ::= { snmpNotifyObjects 1 } snmpNotifyEntry OBJECT-TYPE SYNTAX SnmpNotifyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table selects a set of management targets which should receive notifications, as well as the type of notification which should be sent to each selected management target. Entries in the snmpNotifyTable are created and deleted using the snmpNotifyRowStatus object." INDEX { IMPLIED snmpNotifyName } ::= { snmpNotifyTable 1 } SnmpNotifyEntry ::= SEQUENCE { snmpNotifyName SnmpAdminString, snmpNotifyTag SnmpTagValue, snmpNotifyType INTEGER, snmpNotifyStorageType StorageType, snmpNotifyRowStatus RowStatus } snmpNotifyName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The locally arbitrary, but unique identifier associated with this snmpNotifyEntry." ::= { snmpNotifyEntry 1 } snmpNotifyTag OBJECT-TYPE SYNTAX SnmpTagValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object contains a single tag value which is used to select entries in the snmpTargetAddrTable. Any entry in the snmpTargetAddrTable which contains a tag value which is equal to the value of an instance of this object is selected. If this object contains a value of zero length, no entries are selected." DEFVAL { "" } ::= { snmpNotifyEntry 2 } snmpNotifyType OBJECT-TYPE SYNTAX INTEGER { trap(1), inform(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object determines the type of notification to be generated for entries in the snmpTargetAddrTable selected by the corresponding instance of snmpNotifyTag. This value is only used when generating notifications, and is ignored when using the snmpTargetAddrTable for other purposes. If the value of this object is trap(1), then any messages generated for selected rows will contain Unconfirmed-Class PDUs. If the value of this object is inform(2), then any messages generated for selected rows will contain Confirmed-Class PDUs. Note that if an SNMP entity only supports generation of Unconfirmed-Class PDUs (and not Confirmed-Class PDUs), then this object may be read-only." DEFVAL { trap } ::= { snmpNotifyEntry 3 } snmpNotifyStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row." DEFVAL { nonVolatile } ::= { snmpNotifyEntry 4 } snmpNotifyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5)." ::= { snmpNotifyEntry 5 } snmpNotifyFilterProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpNotifyFilterProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to associate a notification filter profile with a particular set of target parameters." ::= { snmpNotifyObjects 2 } snmpNotifyFilterProfileEntry OBJECT-TYPE SYNTAX SnmpNotifyFilterProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table indicates the name of the filter profile to be used when generating notifications using the corresponding entry in the snmpTargetParamsTable. Entries in the snmpNotifyFilterProfileTable are created and deleted using the snmpNotifyFilterProfileRowStatus object." INDEX { IMPLIED snmpTargetParamsName } ::= { snmpNotifyFilterProfileTable 1 } SnmpNotifyFilterProfileEntry ::= SEQUENCE { snmpNotifyFilterProfileName SnmpAdminString, snmpNotifyFilterProfileStorType StorageType, snmpNotifyFilterProfileRowStatus RowStatus } snmpNotifyFilterProfileName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name of the filter profile to be used when generating notifications using the corresponding entry in the snmpTargetAddrTable." ::= { snmpNotifyFilterProfileEntry 1 } snmpNotifyFilterProfileStorType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this conceptual row." DEFVAL { nonVolatile } ::= { snmpNotifyFilterProfileEntry 2 } snmpNotifyFilterProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the snmpNotifyFilterProfileRowStatus column is 'notReady'. In particular, a newly created row cannot be made active until the corresponding instance of snmpNotifyFilterProfileName has been set." ::= { snmpNotifyFilterProfileEntry 3 } snmpNotifyFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpNotifyFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of filter profiles. Filter profiles are used to determine whether particular management targets should receive particular notifications. When a notification is generated, it must be compared with the filters associated with each management target which is configured to receive notifications, in order to determine whether it may be sent to each such management target. A more complete discussion of notification filtering can be found in section 6. of [RFC2573]." ::= { snmpNotifyObjects 3 } snmpNotifyFilterEntry OBJECT-TYPE SYNTAX SnmpNotifyFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An element of a filter profile. Entries in the snmpNotifyFilterTable are created and deleted using the snmpNotifyFilterRowStatus object." INDEX { snmpNotifyFilterProfileName, IMPLIED snmpNotifyFilterSubtree } ::= { snmpNotifyFilterTable 1 } SnmpNotifyFilterEntry ::= SEQUENCE { snmpNotifyFilterSubtree OBJECT IDENTIFIER, snmpNotifyFilterMask OCTET STRING, snmpNotifyFilterType INTEGER, snmpNotifyFilterStorageType StorageType, snmpNotifyFilterRowStatus RowStatus } snmpNotifyFilterSubtree OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MIB subtree which, when combined with the corresponding instance of snmpNotifyFilterMask, defines a family of subtrees which are included in or excluded from the filter profile." ::= { snmpNotifyFilterEntry 1 } snmpNotifyFilterMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The bit mask which, in combination with the corresponding instance of snmpNotifyFilterSubtree, defines a family of subtrees which are included in or excluded from the filter profile. Each bit of this bit mask corresponds to a sub-identifier of snmpNotifyFilterSubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER matches this family of filter subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of filter subtrees if, for each sub-identifier of the value of snmpNotifyFilterSubtree, either: the i-th bit of snmpNotifyFilterMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of snmpNotifyFilterSubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of snmpNotifyFilterSubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of filter subtrees is the one subtree uniquely identified by the corresponding instance of snmpNotifyFilterSubtree." DEFVAL { ''H } ::= { snmpNotifyFilterEntry 2 } snmpNotifyFilterType OBJECT-TYPE SYNTAX INTEGER { included(1), excluded(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether the family of filter subtrees defined by this entry are included in or excluded from a filter. A more detailed discussion of the use of this object can be found in section 6. of [RFC2573]." DEFVAL { included } ::= { snmpNotifyFilterEntry 3 } snmpNotifyFilterStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this conceptual row." DEFVAL { nonVolatile } ::= { snmpNotifyFilterEntry 4 } snmpNotifyFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5)." ::= { snmpNotifyFilterEntry 5 } -- -- -- Conformance information -- -- snmpNotifyCompliances OBJECT IDENTIFIER ::= { snmpNotifyConformance 1 } snmpNotifyGroups OBJECT IDENTIFIER ::= { snmpNotifyConformance 2 } -- -- -- Compliance statements -- -- snmpNotifyBasicCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for minimal SNMP entities which implement only SNMP Unconfirmed-Class notifications and read-create operations on only the snmpTargetAddrTable." MODULE SNMP-TARGET-MIB MANDATORY-GROUPS { snmpTargetBasicGroup } OBJECT snmpTargetParamsMPModel MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required." OBJECT snmpTargetParamsSecurityModel MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required." OBJECT snmpTargetParamsSecurityName MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required." OBJECT snmpTargetParamsSecurityLevel MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required." OBJECT snmpTargetParamsStorageType SYNTAX INTEGER { readOnly(5) } MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required. Support of the values other(1), volatile(2), nonVolatile(3), and permanent(4) is not required." OBJECT snmpTargetParamsRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access to the snmpTargetParamsTable is not required. Support of the values notInService(2), notReady(3), createAndGo(4), createAndWait(5), and destroy(6) is not required." MODULE -- This Module MANDATORY-GROUPS { snmpNotifyGroup } OBJECT snmpNotifyTag MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required." OBJECT snmpNotifyType SYNTAX INTEGER { trap(1) } MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required. Support of the value notify(2) is not required." OBJECT snmpNotifyStorageType SYNTAX INTEGER { readOnly(5) } MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access is not required. Support of the values other(1), volatile(2), nonVolatile(3), and permanent(4) is not required." OBJECT snmpNotifyRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Create/delete/modify access to the snmpNotifyTable is not required. Support of the values notInService(2), notReady(3), createAndGo(4), createAndWait(5), and destroy(6) is not required." ::= { snmpNotifyCompliances 1 } snmpNotifyBasicFiltersCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which implement SNMP Unconfirmed-Class notifications with filtering, and read-create operations on all related tables." MODULE SNMP-TARGET-MIB MANDATORY-GROUPS { snmpTargetBasicGroup } MODULE -- This Module MANDATORY-GROUPS { snmpNotifyGroup, snmpNotifyFilterGroup } ::= { snmpNotifyCompliances 2 } snmpNotifyFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which either implement only SNMP Confirmed-Class notifications, or both SNMP Unconfirmed-Class and Confirmed-Class notifications, plus filtering and read-create operations on all related tables." MODULE SNMP-TARGET-MIB MANDATORY-GROUPS { snmpTargetBasicGroup, snmpTargetResponseGroup } MODULE -- This Module MANDATORY-GROUPS { snmpNotifyGroup, snmpNotifyFilterGroup } ::= { snmpNotifyCompliances 3 } snmpNotifyGroup OBJECT-GROUP OBJECTS { snmpNotifyTag, snmpNotifyType, snmpNotifyStorageType, snmpNotifyRowStatus } STATUS current DESCRIPTION "A collection of objects for selecting which management targets are used for generating notifications, and the type of notification to be generated for each selected management target." ::= { snmpNotifyGroups 1 } snmpNotifyFilterGroup OBJECT-GROUP OBJECTS { snmpNotifyFilterProfileName, snmpNotifyFilterProfileStorType, snmpNotifyFilterProfileRowStatus, snmpNotifyFilterMask, snmpNotifyFilterType, snmpNotifyFilterStorageType, snmpNotifyFilterRowStatus } STATUS current DESCRIPTION "A collection of objects providing remote configuration of notification filters." ::= { snmpNotifyGroups 2 } END